Small engine repair quote calculator

Build a repair quote job by job: hours at your labour rate, parts at your cost plus your markup, the diagnostic fee handled your way, and storage for machines left behind.

  • One row per job
  • Diagnostic credit shown plainly
  • Storage line kept separate

Before you run the numbers

One quote, every job on its own line

A small engine repair quote is rarely one job. A mower or trimmer comes in for one fault and needs two or three pieces of work, each with its own time and its own parts. A single lump sum hides that, and the customer cannot tell what they are approving.

This calculator keeps each job on its own row. Enter your labour rate, the hours and parts for every job, your markup, and the fee lines, and see the quote build up line by line.

Your numbers

1. Your labour rate

2. Jobs on this machine

Job 1

Job names are yours to write. The examples in the placeholder are prompts only: no hours and no prices are preset for any job.

3. Parts markup

%

4. Diagnostic fee

5. Storage for an uncollected machine

Result

Quote total

Enter your own rate, hours, and parts costs on the left to see the quote.

Short answer

A small engine repair quote calculator builds a quote job by job: hours times your labour rate, plus parts at your cost with your markup added, for each job. It then adds the diagnostic fee, credited or not, and any storage fee, and shows an itemised total.

What the quote covers

What goes into a small engine repair quote?

The quote has four kinds of line. Labour is the time each job takes, priced at your rate per hour. Parts are what each job needs, priced at your cost with your markup added. Those two lines repeat for every job on the machine, so each job shows its own subtotal.

The diagnostic fee covers finding the fault. It is a flat fee, and shops handle it two ways: some credit it against the repair when the customer goes ahead, and some charge it on top. The calculator follows the policy you set, and when the fee is credited it shows the fee and the credit as two lines that cancel out.

The last line is storage. A finished machine that is not collected takes up bench and floor space, so shops charge a fee per day for holding it. That fee is yours to set, and it only appears on the quote when you enter days stored.

Quote partWhat it coversHow it is priced here
LabourThe time spent on each job on the machineHours for the job times your labour rate per hour
PartsThe parts fitted for each jobYour parts cost for the job, with your markup percentage added
Diagnostic feeFinding the fault before repair work startsYour flat fee, credited against the job or charged on top, as you set it
Storage feeHolding a finished machine that has not been collectedYour fee per day times the days the machine is stored

The math

How the quote total is worked out

Each job is priced the same way: its hours times your labour rate, plus its parts cost with your markup added. The quote adds the job subtotals together, then adds the diagnostic fee net of any credit, then adds the storage line.

Per job = Hours x Rate + Parts x (1 + Markup)
Quote = Jobs total + Diagnostic net of credit + Storage per day x Days

Example: a labour rate of $60 per hour and a parts markup of 20 percent, using example figures throughout. A tune-up at 1.5 hours gives $90 of labour, and its parts at $40 come to $48 with the markup, so the job is $138. Carburettor work at 2 hours gives $120 of labour, and its parts at $85 come to $102 with the markup, so the job is $222.

Tune-up: 1.5 x $60 + $40 x 1.2 = $90 + $48 = $138
Carburettor work: 2 x $60 + $85 x 1.2 = $120 + $102 = $222

The two jobs add to $360. A diagnostic fee of $50 is credited against the job in this example, so the fee line of $50 and the credit line of $50 cancel out. Storage at $10 per day for 5 days adds $50.

Quote: $360 + $50 - $50 + $50 = $410

Every figure in this example is a made-up input chosen to show the math. Your quote will use the rate, hours, parts, and fees you enter.

Getting it right

How to build a quote the customer can check

A quote the customer can follow line by line gets approved faster and argued about less. Four steps keep it that way.

  • 01

    List each job on its own row

    A machine often needs more than one job: a tune-up, plus belt work, plus a carburettor clean. One row per job, each with its own hours and parts, keeps the quote readable and makes it easy to drop a job the customer does not want.

  • 02

    Price hours and parts from the job in front of you

    Hours and parts cost change from machine to machine, even for the same job name. Work from the machine on the bench: the hours you expect it to take and the parts it actually needs, at your own rate and your own parts costs.

  • 03

    Settle the diagnostic fee before work starts

    Agree up front whether the diagnostic fee is credited against the repair or charged on top, and set the toggle to match. Showing both the fee line and the credit line on the quote stops the fee becoming a dispute when the bill arrives.

  • 04

    Agree storage terms at drop-off

    Tell the customer the storage fee per day and when it starts when they leave the machine, not when they come back for it. Enter the days stored and the quote shows the storage line on its own, next to the repair lines it sits apart from.

Frequently asked questions

Straight answers to what buyers ask before they scope. Still stuck? .

A repair quote lists the labour for each job, the parts for each job with the shop markup added, the diagnostic fee and how it is handled, and a storage fee if the finished machine sits uncollected. Each part sits on its own line, so the customer can see what the total is made of. Every figure in this calculator is one you enter yourself.
Labour is the hours a job takes times the shop rate per hour. Each job carries its own hours, so a short job and a long job are priced apart rather than blended into one figure. Enter your own rate per hour and the hours for each job, and the calculator works out the labour line for every row.
You enter what the parts for a job cost you, and the calculator adds your markup percentage on top. Parts that cost 100 with a markup of 20 percent are quoted at 120. One markup figure applies to the parts on every job in the quote, which keeps the parts lines consistent from job to job.
The diagnostic fee is your flat charge for finding the fault. Some shops credit it against the repair when the customer goes ahead, and some charge it on top. Set the toggle to match your own policy. If the fee is credited, the quote shows the fee line and a matching credit line, so the customer can see the fee was charged and then taken off.
A storage fee covers a finished machine that stays in the shop because it has not been collected. It is charged per day, at a rate the shop sets, for the days the machine is held. Enter your own fee per day and the number of days, and the calculator adds that line to the quote. Agreeing the fee when the machine is dropped off avoids an argument at collection.
Yes. Enter your labour rate once, add a row for each job on the machine with its hours and its parts cost, set your markup, your diagnostic fee and its credit policy, and any storage line. The result is an itemised quote the customer can read line by line before they approve the work.

The tools give you a range. A call gives you a number.

30-minute scoping call. We will walk through how your shop handles job intake, quotes, and unclaimed machines today, and you leave with a clear plan for the software that runs it.