Gutter cleaning cost calculator

Build a gutter cleaning quote from your own rates: the length of the run, the height of the house, guards, and add-ons. Every price is yours, so the total matches the job in front of you.

  • Your per-foot rate
  • Storey and guard factors
  • Add-ons itemised

Before you run the numbers

One total, built from your own rates

A gutter cleaning quote is not one flat price. The length of the run sets the base, the height of the house changes the work, and guards add handling on every foot. When those parts are bundled into a single figure, it is hard to tell what you are paying for.

This calculator keeps the parts separate. Enter the length, your own price per linear foot, and your own surcharges, and see the total build up line by line.

Your numbers

1. The gutter run

ft

Measure along the eaves where the gutters run, and add each run together.

2. Height of the house

%

The surcharge applies once for each storey above the first.

3. Gutter guards

4. Add-ons

Result

Estimated total

Enter your own prices on the left to see the total.

Short answer

A gutter cleaning cost calculator works out a quote from your own figures: the gutter length, your price per linear foot, a storey factor for each extra level, a guard surcharge when gutter guards are fitted, and any add-ons you select. The total uses only the rates you enter.

What the cost covers

What goes into the price of gutter cleaning?

The price of gutter cleaning covers a short list of parts. The first is the cleaning itself: the length of gutter to be cleared, priced per linear foot. That length is the base of the whole quote, so it pays to measure it with care.

The second part is height. A run above the first storey takes longer ladders, more moves along the wall, and more care, so many quotes add a surcharge for each extra storey. The third part is gutter guards. Guards have to be lifted, the debris under them cleared, and the guards fitted back, which adds handling to every foot of the run.

The last part is add-on work you agree to on top of the clean. A downspout flush clears a blockage so water can leave the gutter. A minor repair fixes a small fault found during the clean. Each add-on is priced on its own, and this calculator asks you to enter every price rather than guessing one for you.

Cost partWhat it coversHow the price is set
Base cleaningThe gutter run itself, measured in linear feet and cleared of leaves and debrisYour price per linear foot
Extra storeysWorking higher up, with longer ladders and more time on each runYour surcharge for each storey above the first
Gutter guardsLifting the guards, clearing underneath them, and fitting them backYour surcharge when guards are fitted
Downspout flushClearing a blocked downspout so water runs away freelyYour price for the add-on, if selected
Minor repairA small fix found during the clean, such as resealing a jointYour price for the add-on, if selected

The math

How the total is worked out

Start with the length multiplied by your price per linear foot. Multiply that by the storey factor, which is 1 plus the number of storeys above the first times your per-storey surcharge. If guards are fitted, multiply by the guard factor, which is 1 plus your guard surcharge. Then add the price of each add-on you selected.

Total = Length x Price per foot x Storey factor x Guard factor + Add-ons

Example: an example gutter length of 100 feet at an example price of $2 per linear foot comes to $200. The house in this example has 2 storeys and an example per-storey surcharge of 25%, so the storey factor is 1.25 and the running total is $250. Guards are fitted in this example, with an example guard surcharge of 20%, so the guard factor is 1.20 and the running total is $300. An example downspout flush at $50 and an example minor repair at $40 bring the total to $390.

100 x $2 x 1.25 x 1.20 + $50 + $40 = $390

The per-foot view on that example total is $390 divided by 100 feet, which is $3.90 per linear foot. Every figure in this example is a made-up input chosen to show the math. Your total will use the rates you enter.

Getting it right

How to get an accurate gutter cleaning quote

The total is only as good as the figures behind it. Four steps keep a quote accurate and free of surprises later.

  • 01

    Measure the run honestly

    Walk the house and measure each gutter run along the eaves, then add the runs together. A length guessed from the front of the house alone misses the back and side runs, and every other line in the quote is built on that length.

  • 02

    Quote guards as their own line

    If the house has gutter guards, say so in the quote and show the guard surcharge as its own part of the price. The customer can then see why a guarded house costs more to clean than the same house without guards.

  • 03

    Count the storeys before you price

    Confirm how many storeys the work reaches before you quote. The surcharge applies once for each storey above the first, so a miscounted house changes the total and the ladder work on the day.

  • 04

    Agree add-ons in writing first

    A downspout flush or a minor repair is easy to add once you are on site, and easy to argue about afterwards. Agree the price for each add-on before the work starts, so the final bill matches the quote the customer accepted.

Frequently asked questions

Straight answers to what buyers ask before they scope. Still stuck? .

A gutter cleaning quote covers the cleaning itself, priced from the length of the gutter run and the price per linear foot. It then adjusts for the height of the house and for gutter guards if they are fitted, and adds any extra work you agree to, such as a downspout flush or a minor repair. Each part is shown as its own line in this calculator, and every price in it is one you enter yourself.
Taller houses take longer to clean and need longer ladders and more care at height. This calculator handles that with a surcharge you set for each storey above the first. A two-storey house adds your surcharge once, a three-storey house adds it twice, and so on. Enter the percentage your business uses, and the storey factor follows from the count you enter.
Gutter guards sit over the gutter, so the cleaner has to lift them, clear the debris underneath, and fit them back in place. That extra handling takes time on every run. If guards are fitted, turn the guard toggle on and enter your own surcharge percentage, and the calculator applies it to the cleaning part of the quote.
Measure along the eaves where the gutters actually run, and add each run together. Include the runs at the front, the back, and the sides of the house if they carry gutters. If you are working from a house perimeter estimate, count only the sides that have gutters fitted. An honest measurement matters more than a fast one, because the length drives the whole quote.
This calculator carries two add-ons, each at a price you enter. A downspout flush clears a blockage in the downspout so water can run away freely. A minor repair covers a small fix found during the clean, such as resealing a leaking joint. Tick only the add-ons the job needs, and each one appears as its own line in the total.
Yes. A company can enter its own price per linear foot, its surcharge for each extra storey, and its surcharge for cleaning gutters with guards fitted, then add the add-on prices for the job. The result is an itemised quote the customer can read line by line, with a per-foot view of the total when the length is entered.

The tools give you a range. A call gives you a number.

30-minute scoping call. We will walk through how your team handles quotes, scheduling, and repeat cleans today, and you leave with a clear plan for the software that runs it.